100 welcome sign east end qr code redstone

Welcome to the Redstone Quarry Trail (east end) 

the trail is x mile/s long and should take about x time for round trip tour

Eastern entrance gate

Walk around the gate. Be sure to carefully read the signs. 

what are rules of parking here? 

next stop will be (insert image)

x

School 

two room school, steam whistle 

location of church 

info on Redstone Church from Hounsell, 196, 

small non-denominational church built by I.C. Pert. 

insert here about the houses and street names 

train tracks 

This sidetrack was a  second set of railroad tracks was covered with asphalt leading into the trees on both sides

notice the cracks in the asphalt under which the train tracks are covered. 

This was the "side track" or siding where train cars could be set aside so as not to stop the regular train traffic on the main line.  

Credit for swenson, russack, cottrell, hhr, chs, etc.




Also a link and qr code to the survey here? Or?

xyz

090 tumbler site and office qr code redstone

abc

ghi

Here is a photo showing the concrete structure and the rock tumbler before it was stolen. From the website here and the webpage here. (This Rock Tumbler was stolen out of the quarry in 2010 for scrap metal. Photo courtesy Stephen Thomas collection). need to get permission to use this photo. 

Joe Viger photo of stolen tumbler 

x 

Here is a picture of how the office used to look 

insert picture of it from the inside too. 

xyz

080 carpenter shop qr code redstone

abc

Just down the road to the left are the remains of the carpenter shop.  

This building should probably be boarded up or removed for safety reasons. 

ghi




xyz

070 quarry site qr code

abc

derrick and its "bull wheel" wetland protection, conservation 

x

x 

Green quarry, full of ground water, at the top of the one-way, winch rail line. Remnants remain of three wooden derricks, an engine house and "tugger" winch (1893) which retracted a rail car from the end of an extensive quarry dump. Parts of two derricks are obvious within the quarry hole while the third, "stiff-leg" derrick was higher up in the back SE corner of the quarry. When viewing the latter remnants one may note an excellent example of a "clovis" arrangement of hardware which is the anchor for a guy-wire attached  to the top of a derrick.

x 

ghi




xyz

060 lathe house qr code

abc

x

Now let's look at the lathe inside the building. 

How it worked 

Note: The sundial at the east entrance and the pilaster near the west entrance were turned on this lathe. 

A tree has grown in the middle of the lathe cradle. Should we cut it? 

x

x

leather belts were connected to the drive above. 

Some of these belts may have been made at Page Belting Company in Concord, NH. Tie to NHDCR info if they have it. As of 2021 the company is still in business. See this link here. 

It was made by the Betts Machine Co. in Wilmington, Delaware 

which photo looks better on a cell phone? click on images to enlarge them.  

For more on this company see this link here. 

There is a second lathe outside. 

x 

knuckle joints 

x 

How to explain these gears and gizmos? 

x 

x 

x 

x 

option A take the wider road up

x

This is the 

ghi




xyz

050 stone shed qr code redstone

abc

Stone shed and blacksmith's forge with fire brick, parts of which have been stolen for scrap metal. The location is in the NNE corner of the original, 500 foot long, wooden stone shed. A cut guy wire from "Matron's" derrick is still visible on the ground while the two photos illustrate what was stolen for scrap metal (2012). 

tool sharpening shed device on the right 

was inside the stone shed 

be careful of the open drain (this should be covered) 

x 

Notice the foundation wall for the wooden shed that was here that covered the tool sharpening station. 

The photo below by Joe Viger shows the stolen blacksmith forge and metal plates. 

Is that forge seen above actually over by the tumbler site? 

see photo here from there

Is this the forge from the tool sharpening site? 

several views of the stone shed 

dimensions 

note the site was cleared of trees then

you could see the homes in the village from the stone shed 

Here is view of the shed 

in this photo notice the ornately carved Corinthian capitals and the web of derricks and wires in the background 

here see "back" side of the post 42 looking at the intersection beyond. Should be able to see from one sign post and/or blaze to the next so easy to follow the trail. 

ghi




xyz

040 qr code steam engines redstone

abc

Two coal- fired boilers and two giant air compressor-steam engine flywheel combinations were originally enclosed within the same building. Boiler fronts are gone and a number of metal parts have been stolen for scrap metal. The boilers provided steam to power the engines which in turn drove the compressors that provided air for pneumatic tools in the quarries and stone sheds. The large air compressors, built by Chicago Pneumatic Tool Co., were installed in 1903 and 1905.

x 

stamped "Governor 4" 

x 

stamped "Governor 3 1/2" 

x 

Stamped, embossed "Chicago Pneumatic Tool Co." 

The photo below shows what the boiler plate or door would have looked like. 

There are more metal items in the woods along here 

ghi




xyz